Skip to Content

FAQ: Buying Wood for Craft Projects

Affiliate Disclosure: As an Amazon Associate I earn from qualifying purchases. Additionally, I may get commissions for purchases made through other affiliate links in this post.

Recently, I’ve had a few requests emailed to me about where to buy wood for Silhouette or Cricut craft projects.

While I consider Mr. Cutting for Business and I amateur wood workers, we have successfully built our 10 seat dining room table, a faux fireplace mantle, an oversized outdoor corner bench, and countless painted wall signs. 

Here are answers to frequently asked questions about buying wood for craft projects.

FAQ: Buying Wood for Craft Projects - cuttingforbusiness.com

FAQ: Buying Wood for Craft Projects

Q: Where should I buy wood for craft projects?

A: I buy wood at my local home improvement center, like Lowe’s or Home Depot. Occasionally, I’ll head over to Lumber 84.

Q: What kind of wood should I buy for my craft project?

A: I buy pine because it is most affordable. Within the selection of pine, I buy the “select” boards which are slightly more expensive, but the wood is higher quality.

Q: How is wood measured and priced?

A: Wood is sold per foot in stores and labeled in feet and inches. For example, a 1 x 4 x 8 board is 1 inch thick, 4 inches wide, and 8 feet long; while a 2 x 6 x 10 is 2 inches thick, 6 inches wide, and 10 feet long.

Q: What are nominal measurements?

An important note: In the wood buying world there is something referred to as “actual vs. nominal” measurements. Even though I just told you that a 1 x 4 x 8 board is 1 inch thick, 4 inches wide, and 8 feet long, and that’s what you’ll see it labeled as at the store – it really isn’t.

The nominal measurements are slightly less than the advertised sizes. A 1 x 4 x 8 board actually measures 3/4 x 3-1/2 x 8ish. So, if you need specific sized wood for a project be sure to measure what you are buying. I never head out to buy wood without a tape measure in my pocket.

Q: What should I look for when buying wood?

A: You should inspect each piece of wood for knots (some knots are not a problem and add character, while very dark knots are likely to fall out of the wood), cupping or crowning (this means that the wood is bowed one way or the other rather than flat), or large shakes (these are cracks within the wood).

To check for cupping or crowning, stand at one end of the board at look down the length of it. In most cases, you’ll see if it isn’t straight. You should try to buy wood that is as straight as possible.

Q: I don’t have power tools at home, will the store cut it for me?

A: Yes, home improvement centers will cut wood to size for you. Most stores will make 2-3 cuts for free, then charge between $.25 and $.50 per additional cut. Store policies vary greatly on wood cutting rules. For example, our Lowe’s will not make cuts smaller than 12 inches.

Q: Is the wood ready to use when I get home?

A: No, all wood should be sanded before painting or adding vinyl. Sandpaper comes in different grits. The larger the number, the finer the grit on the sandpaper. I don’t waste time sanding anything by hand.

An electric palm sander cuts out a huge amount of work and can be picked up in store for around $30. I prefer DeWalt tools and own this model, which includes a nice carrying case.

Q: How can I get free wood?

A: If you are at your local home improvement center and can make use of smaller cuts of wood, ask if they have any scraps. Many stores will give you their scraps for no charge.

If you’ve been pinning things on Pinterest to make with wood, I urge you to take the plunge.

Stenciled or painted signs with help from your Silhouette or Cricut are great sellers.

Click here to cancel reply.

Kathy Hughson

Sunday 21st of October 2018

Do you use anything for the knots so that they don't leak through the final project? Will it leak through if not treated if working with vinyl transfer? Also concerned if using a stencil with paint and the knots leaking through...??

thanks in advance, Kathy

Christine

Sunday 4th of November 2018

No. I embrace the knots and usually ignore them. I believe that they are part of the character of each sign.

Jo Sess

Friday 23rd of February 2018

From the article, it looked like pine is the suggested go to for a reasonable price. However, in what circumstances would you use more high end wood?

Christine

Tuesday 27th of February 2018

Hi Jo! If you want to go with a higher end wood, it's your choice. Just be sure to price accordingly.

Julia

Monday 27th of November 2017

What type of wood would you use on the back of the signs to plank them together? Everything I've used so far likes to split once I start to screw them together. Any helpful tips?

Christine

Tuesday 28th of November 2017

Hi Julia! Honestly, you can use whatever wood you'd like. If your wood is splitting, there's a few things you can try: 1) Drill a pilot hole before screwing your screw in. 2) Rub your screw with wax before screwing it in to lubricate it. 3) Don't place screws within an inch of the end of the board.

Heather

Thursday 16th of November 2017

Hi. I want to send you a picture of something I am trying to make. Can you please email me! Mzplaza13@yahoo

Christine

Friday 17th of November 2017

Feel free to email me using the contact form on the blog or christine@cuttingforbusiness.com.

Gin

Tuesday 7th of November 2017

What grit of sandpaper do you use for making your wood signs?

Christine

Wednesday 8th of November 2017

Hello! See this post: https://cuttingforbusiness.com/2017/10/19/how-to-sand-wood-painted-signs/